We design and manufacture motors, motor controllers, PCBs and power electronics.
Navami Technologies is an engineering and manufacturing company based in India. We take a product from the first drawing through development, prototyping and production, and we have been doing this for customers in India and abroad since 2021.
Our products
Most of our work is in EV and drone powertrains, but the same team builds for defence, medical, automobile and aerospace customers. Select a product to see what we do.
PCBs
We do schematic design, PCB layout and assembly. Most of the boards we build are motor controllers and power electronics, but we also take on control and sensor boards. Before a board goes for fabrication we check it for manufacturability, so the first batch comes back right.
What we do
- Schematic design and PCB layout
- Multilayer boards
- Assembly and testing
- Motor controller and power boards
Motors
We design and build electric motors for EV and drone powertrains. Each motor is sized for the vehicle or aircraft it goes into and tested before it leaves us. We also make motors for medical and defence equipment, where the requirements are stricter.
What we do
- EV and drone traction motors
- Motors for medical and defence equipment
- Custom windings
- Bench testing
Actuators
Our actuators combine a motor, drive electronics and the mechanism in one unit. They are used where a customer needs controlled, repeatable movement. We design the electrical and mechanical parts together, which keeps the unit compact and easier to service.
What we do
- Linear and rotary actuators
- Integrated drive electronics
- Mechanism design
- Testing to your duty cycle
Transformers
We design and build power and signal transformers and other custom magnetics. Each one is made for its application: the voltage, current, frequency and temperature it will actually see in service.
What we do
- Power transformers
- Signal transformers
- Custom inductors and magnetics
- Thermal checks
Simulation
Before we build a prototype, we simulate it. Electrical, thermal, electromagnetic and structural analysis shows us where a design will have problems, and it is cheaper to fix them on screen than on the bench. We also do simulation work for customers who have their own designs.
What we do
- Electromagnetic analysis for motors and magnetics
- Thermal analysis
- Structural analysis
- Circuit simulation
How we work
Every product goes through the same four steps. The same engineers stay with it from start to finish, so nothing gets lost between the design office and the shop floor.
Design
We start with your requirement, drawing or specification and turn it into an electrical, electronic and mechanical design. We review it with you before anything is built.
- Requirements and specification
- Schematic and CAD
- Electrical and thermal sizing
- Design review with you
Development
Detailed engineering: circuit design, firmware, component selection and mechanical detailing. This is where the design is worked out down to the last part.
- Detailed circuit design
- Firmware
- Component selection
- Mechanical detailing
Prototyping
We build the first units and test them on our bench. If something needs to change, we change it here, not in production.
- First units built
- Bench testing
- Design corrections if needed
Manufacturing
Once the prototype is approved we set up tooling and assembly and produce the parts. Every unit is inspected and tested before it ships.
- Tooling and assembly set-up
- Production
- Inspection and testing
Industries we serve
Our customers make equipment where a failure is expensive. That shapes how we design and test.
-
Defence
Rugged electronics and electro-mechanical assemblies for demanding conditions.
Typical work: rugged assemblies, motors, control boards. -
Medical
Motors and power components for medical equipment, where reliability and consistency matter.
Typical work: motors, actuators, power supplies. -
Automobile
Controllers, motors and magnetics for automotive suppliers and OEMs.
Typical work: controllers, motors, magnetics. -
EV
Powertrain components, motor controllers and power electronics for electric vehicles.
Typical work: traction motors, controllers, power electronics. -
Aerospace
Lightweight powertrain components and electronics for drones and aircraft systems.
Typical work: drone motors, controllers, lightweight magnetics.
About Navami Technologies
Navami Technologies was started in 2021 in India. We are an engineering company first: our people design, develop, prototype and manufacture electrical, electronic and electro-mechanical products, and we have done this for customers in India and overseas. Most of our work is in EV and drone powertrains, motor controllers and power electronics, alongside PCBs, motors, actuators, transformers and simulation work for defence, medical, automobile and aerospace customers.
More about usHave a requirement?
Send us a drawing, a specification or even a short description of what you need. We will come back with questions and a quote.